STM32 IIC 实验

news/2025/2/11 4:58:48/

1.

 可以选择I2C1，也可以选择I2C2，或者同时选择，同时运行

 

配置时钟信号

为节约空间，选择这两个，然后选择GENERATE CODE

二、HAL_I2C_Mem_Write

I2C_HandleTypeDef *hi2c：I2C设备句柄
uint16_t DevAddress：目标器件的地址，七位地址必须左对齐
uint16_t MemAddress：目标器件的目标寄存器地址
uint16_t MemAddSize：目标器件内部寄存器地址数据长度
uint8_t *pData：待写的数据首地址
uint16_t Size：待写的数据长度
uint32_t Timeout：超时时间
返回值： HAL_StatusTypeDef ， HAL 状态（ OK ， busy ， ERROR ， TIMEOUT ）
向OLED写入命令的封装： 
void Oled_Write_Cmd(uint8_t dataCmd)
{HAL_I2C_Mem_Write(&hi2c1,0x78,0x00,I2C_MEMADD_SIZE_8BIT,&dataCmd,1,0xff);
}
向 OLED 写数据的封装：最大的区别是目标器件的目标寄存器地址变成了0x40 
void Oled_Write_Data(uint8_t dataData)
{
HAL_I2C_Mem_Write(&hi2c1,0x78,0x40,I2C_MEMADD_SIZE_8BIT,&dataData,1,0xff);}

 三、初始化Oled（官方手册上面有）,清屏函数，调入图片的亮点到数组，显示函数。

初始化Oled:

void Oled_Init(void){
Oled_Write_Cmd(0xAE);//--display offOled_Write_Cmd(0x00);//---set low column addressOled_Write_Cmd(0x10);//---set high column addressOled_Write_Cmd(0x40);//--set start line address  Oled_Write_Cmd(0xB0);//--set page addressOled_Write_Cmd(0x81); // contract controlOled_Write_Cmd(0xFF);//--128   Oled_Write_Cmd(0xA1);//set segment remap Oled_Write_Cmd(0xA6);//--normal / reverseOled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)Oled_Write_Cmd(0x3F);//--1/32 dutyOled_Write_Cmd(0xC8);//Com scan directionOled_Write_Cmd(0xD3);//-set display offsetOled_Write_Cmd(0x00);//Oled_Write_Cmd(0xD5);//set osc divisionOled_Write_Cmd(0x80);//Oled_Write_Cmd(0xD8);//set area color mode offOled_Write_Cmd(0x05);//Oled_Write_Cmd(0xD9);//Set Pre-Charge PeriodOled_Write_Cmd(0xF1);//Oled_Write_Cmd(0xDA);//set com pin configuartionOled_Write_Cmd(0x12);//Oled_Write_Cmd(0xDB);//set VcomhOled_Write_Cmd(0x30);//Oled_Write_Cmd(0x8D);//set charge pump enableOled_Write_Cmd(0x14);//Oled_Write_Cmd(0xAF);//--turn on oled panel	}

清屏函数

void Oled_Screen_Clear(void){char i,n;Oled_Write_Cmd (0x20);                    //set memory addressing modeOled_Write_Cmd (0x02);                    //page addressing modefor(i=0;i<8;i++){Oled_Write_Cmd(0xb0+i);               //éè??ò3μ??·￡¨0~7￡?Oled_Write_Cmd(0x00);                 //éè????ê??????aáDμíμ??·Oled_Write_Cmd(0x10);                 //éè????ê??????aáD??μ??·   for(n=0;n<128;n++)Oled_Write_Data(0x00); 			}	
}

设置图片的点阵,可以通过电脑画图软件画

通过取模软件生成数据将图片的亮点放到数组：

unsigned char bmpImager[] = {/*--  调入了一幅图像：E:\丁1.bmp  --*/
/*--  宽度x高度=128x64  --*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,
0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0xC0,0xC0,0xC0,0xC0,0xC0,0xE0,0xE0,
0xE0,0xE0,0xE0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xE0,0xFC,
0xFF,0x3F,0x0F,0x03,0x01,0x03,0x03,0x03,0x03,0x03,0x03,0x03,0x03,0x03,0x03,0x03,
0x03,0x03,0x03,0x07,0x07,0x07,0x07,0x0F,0x0E,0x0E,0x0E,0x0E,0x0E,0x0E,0x1E,0x1F,
0x1F,0x1F,0x1F,0x3F,0x3F,0x3F,0x3F,0x7B,0x73,0x73,0xF1,0xE1,0xC1,0xC1,0x81,0x80,
0x10,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x3C,0x1C,0x1C,0x1C,
0x1C,0x1E,0x0C,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xFC,0xFF,0x3F,0x07,
0x00,0x00,0x02,0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x87,0xC7,0xC7,0x87,0x07,0x07,
0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x87,0xFF,0xFF,0xFF,0x07,0x07,0x07,0x07,0x07,
0x07,0x07,0x07,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x03,0x03,0x07,
0x07,0x0F,0x1E,0x1E,0x1C,0x3C,0x38,0x78,0xF0,0xF0,0xE0,0xC0,0xC8,0x1C,0x1C,0x1C,
0x1C,0x1C,0x1C,0x1C,0x1E,0x0E,0x0F,0x0F,0x07,0x07,0x03,0x03,0x03,0x03,0x03,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0x01,0x00,0x00,
0x00,0x00,0x00,0x00,0xF0,0xFC,0xFE,0x9F,0xC6,0xF0,0xFF,0x7F,0x1F,0x01,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xFF,0xFF,0x3F,0x00,0x00,0x00,0x00,0x00,0xE0,
0xF0,0xF8,0x7E,0x3F,0x0F,0x07,0x87,0xCF,0xEE,0xFE,0xFE,0x3C,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0xFF,0xFF,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xFF,0xFF,0xF0,0x80,0x00,
0x00,0x00,0x00,0x00,0x03,0x07,0x07,0x07,0x07,0x03,0x01,0x00,0x00,0x80,0xC0,0x80,
0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x03,
0x07,0x0F,0x0E,0x0E,0x0F,0x07,0x07,0x07,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xC0,0xF8,0xFF,0x7F,0x0F,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0F,0x1F,0x7E,
0xF8,0xF0,0xE0,0xC0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,
0x0F,0x1F,0x3E,0x7C,0xF8,0xF8,0xFF,0xFF,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xC0,0xC0,
0xC0,0xE0,0xF0,0x70,0x78,0x3C,0x1E,0x1F,0x0F,0x07,0x03,0x01,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x01,0x01,0x03,0x07,0x07,0x07,0x07,0x0F,0x0E,0x0E,0x0E,0x1E,0x1C,0x1C,0x1C,
0x1C,0x1C,0x1C,0x3C,0x38,0x39,0x39,0x39,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,
0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x38,0x3C,0x1E,0x1F,0x0F,0x07,0x03,0x01,
0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,};

显示函数：

void Oled_Show_Image(unsigned char *image)
{unsigned char i; unsigned int j;for(i=0;i<8;i++){Oled_Write_Cmd(0xB0 + i);//page0--page7//每个page从0列Oled_Write_Cmd(0x00);Oled_Write_Cmd(0x10);//0到127列，依次写入0，每写入数据，列地址自动偏移for(j = 128 * i; j<(128 * (i+1));j++){Oled_Write_Data(image[j]);}}
}

四、主函数

直接在while(1)循环之前添加即可。

//1. OLED初始化Oled_Init();//2. 选择一个位置//2.1 确认页寻址模式Oled_Write_Cmd(0x20);Oled_Write_Cmd(0x02);Oled_Screen_Clear();Oled_Show_Image(bmpImager);


http://www.ppmy.cn/news/1200832.html

相关文章

Python批量下载ERA5数据

Python批量下载ERA5数据

1. ERA5数据简介 ERA5是第五代ECMWF大气再分析全球气候数据(ECMWF)&#xff0c;该数据集的第一部分现在可以公开使用(1979年到3个月内)。ERA5数据提供每小时的大气、陆地和海洋气候变量的估计值&#xff0c;地球数据精确到了30km网格&#xff0c;包括了137层的大气数据。 网址…
阅读更多...
野火霸天虎 STM32F407 学习笔记_2 寄存器介绍

野火霸天虎 STM32F407 学习笔记_2 寄存器介绍

寄存器 虽然正式编程没有必要用寄存器编程&#xff0c;通常都是库函数或者 hal 库。但是还是有必要学一下原理的。 寄存器映射 芯片视图如下。 丝印&#xff1a;芯片上印的信息。型号&#xff0c;内核&#xff0c;生产批次等。 引脚&#xff1a;左上角是有小圆点的&#x…
阅读更多...
项目实战：展示第一页数据

项目实战：展示第一页数据

1、在FruitDao接口中添加查询第一页数据和查询总记录条数 package com.csdn.fruit.dao; import com.csdn.fruit.pojo.Fruit; import java.util.List; //dao &#xff1a;Data Access Object 数据访问对象 //接口设计 public interface FruitDao {void addFruit(Fruit fruit);vo…
阅读更多...
RabbitMQ（高级特性）利用限流实现不公平分发

RabbitMQ（高级特性）利用限流实现不公平分发

在RabbitMQ中&#xff0c;多个消费者监听同一条队列&#xff0c;则队列默认采用的轮询分发。但是在某种场景下这种策略并不是很好&#xff0c;例如消费者1处理任务的速度非常快&#xff0c;而其他消费者处理速度却很慢。此时如果采用公平分发&#xff0c;则消费者1有很大一部分…
阅读更多...
Harbor企业级Registry基础镜像仓库的详细安装使用教程（保姆级）

Harbor企业级Registry基础镜像仓库的详细安装使用教程（保姆级）

Harbor Docker 官方提供的私有仓库 registry&#xff0c;用起来虽然简单 &#xff0c;但在管理的功能上存在不足。 Harbor是vmware一个用于存储和分发Docker镜像的企业级Registry服务器&#xff0c;harbor使用的是官方的docker registry(v2命名是distribution)服务去完成。 ha…
阅读更多...
800*A. Domino piling（规律数学）

800*A. Domino piling（规律数学）

Problem - 50A - Codeforces #include<bits/stdc.h> using namespace std; const int N1e55; int n,m,res; signed main(){scanf("%d%d",&n,&m);if(n>1){resn/2*m;n%2; }if(n1) resm/2;cout<<res;return 0; }
阅读更多...
时序预测 | MATLAB实现基于SVM-Adaboost支持向量机结合AdaBoost时间序列预测

时序预测 | MATLAB实现基于SVM-Adaboost支持向量机结合AdaBoost时间序列预测

时序预测 | MATLAB实现基于SVM-Adaboost支持向量机结合AdaBoost时间序列预测 目录 时序预测 | MATLAB实现基于SVM-Adaboost支持向量机结合AdaBoost时间序列预测预测效果基本介绍模型描述程序设计参考资料 预测效果 基本介绍 1.Matlab实现SVM-Adaboost时间序列预测&#xff08;风…
阅读更多...
通过51单片机控制SG90舵机按角度正反转转动

通过51单片机控制SG90舵机按角度正反转转动

一、前言 本文介绍如何通过51单片机控制SG90舵机实现角度的正反转转动。SG90舵机是一种常用的微型舵机&#xff0c;具有体积小、重量轻、结构简单等特点&#xff0c;被广泛应用于机器人、遥控模型和各种自动控制系统中。 使用51单片机&#xff08;STC89C52&#xff09;作为控…
阅读更多...
最新文章

Copyright @ 2022~2023