【STM32】INA3221三通道电压电流采集模块，HAL库

ops/2024/11/3 2:28:57/

一、简单介绍

芯片的datasheet地址：

INA3221 三通道、高侧测量、分流和总线电压监视器，具有兼容 I2C 和 SMBUS 的接口 datasheet (Rev. B)

笔者所使用的INA3221是淘宝买的模块

原理图

模块的三个通道的电压都是一样，都是POWER。这个芯片采用的是高侧测量：每个通道有两个引脚，一个连接负载去给负载供电，另一个回来，回到GND

经过笔者测量和观察，采样电阻的阻值应该是100mΩ

二、模块与接线

INA3221使用IIC通信协议进行读写，笔者使用的是STM32G030F6P6单片机来操作，读者按实际情况类推即可，cubeMX配置，基本都大差不差。

POWER连接外部电源的正极

GND连接外部电源的负极

将模块的GND与单片机的GND连接起来，注意这里地接在一起，如果单片机连着电脑，请务必小心操作，不要接反也不要短路

三、cubemx配置

设置时钟

用内部的RC震荡就可以了，也可以使用外部晶振，但如果用外部晶振的话，这颗晶振必须是有源的，之前看一些G030的板子焊了一个无源晶振，有点匪夷所思。

设置IIC

打算把电压和电流显示在0.96寸的oled上，因此就开了两个IIC，当然了，只开一个也可以，把INA3221和OLED都接在一个IIC总线上就行了，但为了方便，笔者开了两个。

这里的频率可以开到1Mhz，如果是103C8T6，应该是到不了的😋

数据量很小，DMA就不开了

设置GPIO

由于模块上自带了LED灯，所以就没必要开输入IO口给模块，可以开一个监控单片机程序运行的LED

至此，cubeMX配置完毕

四、keil配置

五、驱动编写

打开手册关于编程的章节

支持快速IIC传输，且高位在前

不管是读还是写，一开始要发一个寄存器指针过去，定位一下寄存器

寄存器读写函数

static void INA3221_ReadReg(INA3221_regType *reg)
{HAL_I2C_Mem_Read(INA3321_I2C, INA3221_I2C_ADDRESS, reg->address, 1, &reg->data, 2, 0xFFFF);DataReverse(reg->data, &reg->data);
}static void INA3221_WriteReg(INA3221_regType *reg)
{DataReverse(reg->data, &reg->data);HAL_I2C_Mem_Write(INA3321_I2C, INA3221_I2C_ADDRESS, reg->address, 1, &reg->data, 2, 0xFFFF);
}

寄存器表

先简单读一下芯片的ID，看看是否能正常通信

读芯片的id号，值是0x2032，但波形是3220，因此要翻转一下高低字节

代码如下

static void DataReverse(uint16_t raw, uint16_t* cook)
{*cook = ((uint8_t)(raw) << 8) | (raw >> 8);
}

读channel的bus电压值

一个位代表8mV，但寄存器里面的左移三位又刚好弥补了这一点，因此直接读到的就是电压值。

代码如下

static void INA3221_Sample_Volt()
{INA3221_ReadReg(&volt1);INA3221_ReadReg(&volt2);INA3221_ReadReg(&volt3);
}

读channel的shunt电压值

一个位代表40uV，满量程是163.8mV，因此这个用的100mΩ的模块最大采集电流为1638mA

shunt可以是负数，代表反向电流，但模块设计成IN-接PWR了，笔者就只实验了正向电流

代码如下

static void INA3221_Calculate_Current(uint32_t* current)
{current[0] = shunt1.data >> 3;/* 40uV per LSB */current[0] *= 4;current[0] = current[0] * 10 / SHUNT_RESISTOR;current[1] = shunt2.data >> 3;/* 40uV per LSB */current[1] *= 4;current[1] = current[1] * 10 / SHUNT_RESISTOR;current[2] = shunt3.data >> 3;/* 40uV per LSB */current[2] *= 4;current[2] = current[2] * 10 / SHUNT_RESISTOR;
}

主函数编写

int main(void)
{/* USER CODE BEGIN 1 *//* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_I2C2_Init();MX_I2C1_Init();/* USER CODE BEGIN 2 */
INA3221_Init();
OLED_Init();
OLED_Clear();
OLED_ShowString(0,0,"C1",16);
OLED_ShowString(0,2,"C2",16);
OLED_ShowString(0,4,"C3",16);/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){INA3221_GetVolt();INA3221_GetCurrent();sprintf(info[0], "%.2fV ", voltage[0]/1000.0f);sprintf(info[1], "%.2fV ", voltage[1]/1000.0f);sprintf(info[2], "%.2fV ", voltage[2]/1000.0f);OLED_ShowString(20,0,info[0],16);OLED_ShowString(20,2,info[1],16);OLED_ShowString(20,4,info[2],16);sprintf(info[3], "%.3fA", current[0]/1000.0f);sprintf(info[4], "%.3fA", current[1]/1000.0f);sprintf(info[5], "%.3fA", current[2]/1000.0f);OLED_ShowString(80,0,info[3],16);OLED_ShowString(80,2,info[4],16);OLED_ShowString(80,4,info[5],16);HAL_GPIO_TogglePin(LED_GPIO_Port,LED_Pin);HAL_Delay(100);/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}

六、效果展示

七、驱动附录

ina3221.h

#ifndef INA3221_H
#define INA3221_H#include"i2c.h"
#include "stdint.h"
#include "main.h"typedef struct
{uint8_t address;uint16_t data;
}INA3221_regType;typedef enum
{CH1,CH2,CH3,
}INA3221_SHUNTChannelType;/*** prepare for mask enable register*/
typedef struct
{uint8_t CF1;uint8_t CF2;uint8_t CF3;uint8_t WF1;uint8_t WF2;uint8_t WF3;
}INA3221_FlagType;extern INA3221_regType dieID;
extern INA3221_regType mask_enable;extern INA3221_regType volt1;
extern INA3221_regType shunt1;
extern INA3221_regType volt2;
extern INA3221_regType shunt2;
extern INA3221_regType volt3;
extern INA3221_regType shunt3;extern uint32_t current[3];
extern uint16_t voltage[3];extern INA3221_FlagType INA3221_flag;void INA3221_Config();
void INA3221_Init();
void INA3221_Reset();
void INA3221_ReadDieID();
void INA3221_ReadmanufactID();
void INA3221_GetVolt();
void INA3221_GetCurrent();#endif

ina3221.c

#include "INA3221.h"#define INA3321_I2C &hi2c1
#define INA3221_I2C_ADDRESS 0x80/*shunt resistor mohm*/
#define SHUNT_RESISTOR 			100#define POWER_VALID_UPPER 		10000#define POWER_VALID_LOWER 		9000/*** register address table*/
typedef enum
{SHUNT_CH1 = 0x01,VOLT_CH1,SHUNT_CH2,VOLT_CH2,SHUNT_CH3,VOLT_CH3,CRITICAL_CH1,WARNING_CH1,CRITICAL_CH2,WARNING_CH2,CRITICAL_CH3,WARNING_CH3,SHUNT_VOLT_SUM,SHUNT_VOLT_SUM_LIMIT,MASK_ENABLE,POWER_VALID_HIGH = 0x10,POWER_VALID_LOW,
}INA3221_RegAddressType;/*** average samples*/
typedef enum
{AVG_1,AVG_4,AVG_16,AVG_64,AVG_128,AVG_256,AVG_512,AVG_1024,
}INA3221_AVGType;/*** average samples*/
typedef enum
{CONV_TIME_140US,CONV_TIME_204US,CONV_TIME_332US,CONV_TIME_588US,CONV_TIME_1_1MS,CONV_TIME_2_116MS,CONV_TIME_4_156MS,CONV_TIME_8_244MS,
}INA3221_CTType;/*** average samples*/
typedef enum
{POWER_DOWN,SHUNT_SINGLE,BUS_SINGLE,SHUNT_BUS_SINGLE,POWER_DN,SHUNT_CONTINUOUS,BUS_CONTINUOUS,SHUNT_BUS_CONTINUOUS,
}INA3221_ModeType;INA3221_regType cfg = {.address = 0};INA3221_regType volt1 = {.address = VOLT_CH1};
INA3221_regType shunt1 = {.address = SHUNT_CH1};
INA3221_regType volt2 = {.address = VOLT_CH2};
INA3221_regType shunt2 = {.address = SHUNT_CH2};
INA3221_regType volt3 = {.address = VOLT_CH3};
INA3221_regType shunt3 = {.address = SHUNT_CH3};INA3221_regType critical_ch1 = {.address = CRITICAL_CH1};
INA3221_regType critical_ch2 = {.address = CRITICAL_CH2};
INA3221_regType critical_ch3 = {.address = CRITICAL_CH3};
INA3221_regType warning_ch1 = {.address = WARNING_CH1};
INA3221_regType warning_ch2 = {.address = WARNING_CH2};
INA3221_regType warning_ch3 = {.address = WARNING_CH3};INA3221_regType mask_enable = {.address = MASK_ENABLE};INA3221_regType power_valid_upper = {.address = POWER_VALID_HIGH};
INA3221_regType power_valid_lower = {.address = POWER_VALID_LOW};INA3221_regType manufactID = {.address = 0xFE};
INA3221_regType dieID = {.address = 0xFF};/* store power voltage */
uint32_t current[3];
/* store power current */
uint16_t voltage[3];INA3221_FlagType INA3221_flag;
/*** exchange data high and low byte for word variable*/
static void DataReverse(uint16_t raw, uint16_t* cook);/*** read register value*/
static void INA3221_ReadReg(INA3221_regType *reg);/*** write register value*/
static void INA3221_WriteReg(INA3221_regType *reg);/*** cacluate voltages from volt register value*/
static void INA3221_Calculate_Volt(uint16_t* volt);/*** cacluate currents from shunt register value*/
static void INA3221_Calculate_Current(uint32_t* current);/*** set limite value for current alert*/
static void INA3221_SetLimit(INA3221_regType *reg, uint16_t volt);/*** just read volt registers*/
static void INA3221_Sample_Volt();/*** just read shunt registers*/
static void INA3221_Sample_Shunt();static void DataReverse(uint16_t raw, uint16_t* cook)
{*cook = ((uint8_t)(raw) << 8) | (raw >> 8);
}static void INA3221_ReadReg(INA3221_regType *reg)
{HAL_I2C_Mem_Read(INA3321_I2C, INA3221_I2C_ADDRESS, reg->address, 1, &reg->data, 2, 0xFFFF);DataReverse(reg->data, &reg->data);
}static void INA3221_WriteReg(INA3221_regType *reg)
{DataReverse(reg->data, &reg->data);HAL_I2C_Mem_Write(INA3321_I2C, INA3221_I2C_ADDRESS, reg->address, 1, &reg->data, 2, 0xFFFF);
}static void INA3221_Calculate_Volt(uint16_t* volt)
{*volt = volt1.data;*(volt + 1) = volt2.data;*(volt + 2) = volt3.data;
}static void INA3221_Calculate_Current(uint32_t* current)
{current[0] = shunt1.data >> 3;/* 40uV per LSB */current[0] *= 4;current[0] = current[0] * 10 / SHUNT_RESISTOR;current[1] = shunt2.data >> 3;/* 40uV per LSB */current[1] *= 4;current[1] = current[1] * 10 / SHUNT_RESISTOR;current[2] = shunt3.data >> 3;/* 40uV per LSB */current[2] *= 4;current[2] = current[2] * 10 / SHUNT_RESISTOR;
}static void INA3221_SetLimit(INA3221_regType *reg, uint16_t volt)
{reg->data = volt;INA3221_WriteReg(reg);
}static void INA3221_Sample_Volt()
{INA3221_ReadReg(&volt1);INA3221_ReadReg(&volt2);INA3221_ReadReg(&volt3);
}static void INA3221_Sample_Shunt()
{INA3221_ReadReg(&shunt1);INA3221_ReadReg(&shunt2);INA3221_ReadReg(&shunt3);
}void INA3221_ReadDieID()
{INA3221_ReadReg(&dieID);
}void INA3221_ReadmanufactID()
{INA3221_ReadReg(&manufactID);
}void INA3221_GetVolt()
{INA3221_Sample_Volt();INA3221_Calculate_Volt(voltage);
}void INA3221_GetCurrent()
{INA3221_Sample_Shunt();INA3221_Calculate_Current(current);
}void INA3221_Config()
{/* read default register value from chip*/INA3221_ReadReg(&cfg);/* store it in config variable */cfg.data |= (cfg.data & !0x0E00) | (AVG_4 << 9);/*bus*/cfg.data |= (cfg.data & !0x01C0) | (CONV_TIME_2_116MS << 6);/*shunt*/cfg.data |= (cfg.data & !0x38) | (CONV_TIME_2_116MS << 3);/* wirte to register value */INA3221_WriteReg(&cfg);INA3221_ReadReg(&cfg);
}void INA3221_Set_Critical(INA3221_SHUNTChannelType channel, uint16_t current)
{switch (channel){case CH1:{/* 40uV per LSB */INA3221_SetLimit(&critical_ch1, (current * SHUNT_RESISTOR / 40) << 3);break;}case CH2:{INA3221_SetLimit(&critical_ch2, (current * SHUNT_RESISTOR / 40) << 3);break;}case CH3:{INA3221_SetLimit(&critical_ch3, (current * SHUNT_RESISTOR / 40) << 3);break;}default:break;}
}void INA3221_Set_Warning(INA3221_SHUNTChannelType channel, uint16_t current)
{switch (channel){case CH1:{INA3221_SetLimit(&warning_ch1, (current * SHUNT_RESISTOR / 40) << 3);break;}case CH2:{INA3221_SetLimit(&warning_ch2, (current * SHUNT_RESISTOR / 40) << 3);break;}case CH3:{INA3221_SetLimit(&warning_ch3, (current * SHUNT_RESISTOR / 40) << 3);break;}default:break;}
}void INA3221_Reset()
{cfg.data = 0x8000;INA3221_WriteReg(&cfg);
}void INA3221_Init()
{INA3221_ReadDieID();/* reset all registers */INA3221_Reset();INA3221_Config();
}

八、补充功能

INA3221还带可编程报警和警告输出

一、关键提示

会去比较每个通道的shunt电压值和相应的预设的值，用来判断是否发生过流

二、警告提示

会去比较每个通道的平均shunt电压值和相应的预设的值，用来判断是否发生过流

三、电源有效提示

芯片默认的PV上限是10V，下限是9V，都是可以改写的

意思是在外部高压输入的时候，如果三个通道的电压均高于10V，那么电源OK

如果电压降低，低于9V，电源不OK，模块的灯就会亮起来，因为这几个提示引脚都是开漏输出的

在外部高压输入的时候，如果有任意通道电压<10V，电源不OK，模块的灯就会亮起来，因为这几个提示引脚都是开漏输出的

如果电压升高，高于10V就可以了

有点像施密特触发器

可以把PV上拉到VPU去，这样电压就抬起来了，也可以在PV引脚和地直接串电阻来降压

模块的输入端子里有VPU，根据实际情况使用即可

四、时序控制提示

九、工程链接

STM32INA3221电压电流实时显示OLED工程资源-CSDN文库


http://www.ppmy.cn/ops/130578.html

相关文章

制作安装k8s需要的离线yum源

制作安装k8s需要的离线yum源

制作安装k8s需要的离线yum源 添加docker在线源制作安装k8s命令行工具需要的离线yum源传到内网k8s节点&#xff0c;通过如下命令导出镜像&#xff1a; 要全内网环境安装docker、k8s和相关依赖&#xff0c;需要在内部提供安装k8s、docker需要的yum源 添加docker在线源 yum-confi…
阅读更多...
优先级队列（PriorityQueue）

优先级队列（PriorityQueue）

优先级队列&#xff08;PriorityQueue&#xff09; 1. PriorityQueue的特性2. PriorityQueue常用方法介绍常用构造方法常用的普通方法 1. PriorityQueue的特性 使用时必须导入PriorityQueue所在的包&#xff0c;即 import java.util.PriorityQueue;PriorityQueue中所放置的元素…
阅读更多...
redolog与binlog的写入机制

redolog与binlog的写入机制

redo log 事务在执行的过程中&#xff0c;生成的redo log是要先写到redo log buffer中的。redo log buffer里面的内容不需要每次生成后都直接持久化到磁盘。 如果事务执行期间MySQL发生异常重启&#xff0c;那这部分日志就丢了&#xff0c;但是由于没有commit&#xff0c;所以…
阅读更多...
el-table 修改高亮行样式

el-table 修改高亮行样式

el-table 修改高亮行样式 <el-table reftable :data"tableData" highlight-current-row></el-table>修改样式 ::v-deep .el-table__body tr.current-row > td {background: #e1e1e1 !important;color: #000 !important; }
阅读更多...
国自然基金项目撰写技巧

国自然基金项目撰写技巧

原文链接&#xff1a;国自然基金项目撰写技巧https://mp.weixin.qq.com/s?__bizMzUzNTczMDMxMg&mid2247625527&idx5&sn47c81dafb938fbc1da19e9a745f7bd5c&chksmfa8daad0cdfa23c6973c85a334373392b3edaad4a6d8661e53cd39e1d02aac5d035cad429cd2&token91245…
阅读更多...
大数据-204 数据挖掘 机器学习理论 - 混淆矩阵 sklearn 决策树算法评价

大数据-204 数据挖掘 机器学习理论 - 混淆矩阵 sklearn 决策树算法评价

点一下关注吧&#xff01;&#xff01;&#xff01;非常感谢&#xff01;&#xff01;持续更新&#xff01;&#xff01;&#xff01; 目前已经更新到了&#xff1a; Hadoop&#xff08;已更完&#xff09;HDFS&#xff08;已更完&#xff09;MapReduce&#xff08;已更完&am…
阅读更多...
MFC文件管理-学习笔记

MFC文件管理-学习笔记

CFileDialog封装用于文件打开操作或文件保存操作的常见对话框&#xff0c;继承于CCommonDialogCFileDialog的公共数据成员&#xff1a;m_ofn:Windows的OPENFILENAME结构&#xff0c;提供对基本文件对话框参数的访问权限。使用CFileDialog对象首先要使用构造参数创建该对象&…
阅读更多...
HCIA笔记

HCIA笔记

目录 一&#xff0c;OIS七层模型 二&#xff0c;拓扑类型 三&#xff0c;节点增加设备----HUB集线器 四&#xff0c;网桥——交换机——工作在介质访问控制层&#xff08;单位&#xff1a;BP-S&#xff09; 五&#xff0c;路由器原理 六&#xff0c;封装与解封装 七&…
阅读更多...
最新文章

Copyright @ 2022~2023