- 现象:console登陆后一直在BootWare界面,且指示灯sys灯黄灯常亮!除g0/0口其他以太网口无法up
- 判断:版本丢失
- 解决方法:命令行BootWare菜单下上传软件版本
- 准备工具
- 网线一根
- console线一根
- MSR830版本包(官网下载,公用用户名:yx800 密钥:01230123)
- tftp软件(软件不唯一,这里用TftpServer.exe)
- 步骤:将网线连接到路由器g0/0,console也要连接上
- 电脑打开TftpServer.exe
- 注意:版本包要和软件在同一个目录下如下:
-
- 用终端软件(secureCRT)登入
-
-
路由器上电和重新启动的过程中,在配置终端的屏幕上首先将显示:
****************************************************************************
* *
* H3C MSR930 BootWare, Version 5.02 *
* *
****************************************************************************
Copyright (c) 2004-2014 Hangzhou H3C Technologies Co., Ltd.
Compiled Date : Dec 8 2014
CPU Type : P1010
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
CPU Clock Speed : 533MHz
Memory Type : DDR3 SDRAM
Memory Size : 256MB
Memory Speed : 667MHz
BootWare Size : 1024KB
Flash Size : 128MB
CPLD Version : 1.0
PCB Version : 3.0
BootWare Validating...
Press Ctrl+B to enter extended boot menu... //当系统出现“Press Ctrl+B to enter extended boot menu...”时,马上按下<Ctrl+B>
BootWare password: Not required. Please press Enter to continue. //按Enter键系统进入BootWare主菜单
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System
|<2> Enter Serial SubMenu
|<3> Enter Ethernet SubMenu
|<4> File Control
|<5> Restore to Factory Default Configuration
|<6> Skip Current System Configuration
|<7> BootWare Operation Menu
|<8> Clear Super Password
|<9> Storage Device Operation
|<0> Reboot
============================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3 //在BootWare菜单下键入<3>,可以进入以太网口子菜单
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash
|<1> Download Application Program To SDRAM And Run
|<2> Update Main Application File
|<3> Update Backup Application File
|<4> Update Secure Application File
|<5> Modify Ethernet Parameter
|<0> Exit To Main Menu
|<Ensure The Parameter Be Modified Before Downloading!>
============================================
Enter your choice(0-5): 5 //键入<5>,修改以太网口参数
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field.
| '-' = Go to previous field.
| Ctrl+D = Quit.
============================================
Protocol (FTP or TFTP) :ftp tftp //选择传输协议,根据实际情况选择,本案例使用tftp协议进行传输
Load File Name :zpceshi.bin
:MSR800-CMW520-R2516P24.BIN //下载文件名,要与下载的实际文件名一致
Target File Name :zpceshi.bin
:MSR800-CMW520-R2516P24.BIN //存储的目标文件名。缺省情况下与服务器端文件名一致
Server IP Address :192.168.1.1 192.168.1.10 //TFTP/FTP服务器的IP地址
Local IP Address :192.168.1.2 192.168.1.1 //本地IP地址,为TFTP/FTP客户端设置的IP地址
Gateway IP Address :0.0.0.0 //网关IP地址。当与服务器不在同一网段时需要配置网关地址,否则直接键入<enter>即可
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash
|<1> Download Application Program To SDRAM And Run
|<2> Update Main Application File
|<3> Update Backup Application File
|<4> Update Secure Application File
|<5> Modify Ethernet Parameter
|<0> Exit To Main Menu
|<Ensure The Parameter Be Modified Before Downloading!>
============================================================================
Enter your choice(0-5): 2 //键入<2>为升级主启动文件
Loading.....................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
......................................Done!
32570368 bytes downloaded!
Updating File flash:/MSR93X-CMW520-R2514P14.BIN.............................
............................................................................
............................................................................
......................................................................Done!
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash
|<1> Download Application Program To SDRAM And Run
|<2> Update Main Application File
|<3> Update Backup Application File
|<4> Update Secure Application File
|<5> Modify Ethernet Parameter
|<0> Exit To Main Menu
|<Ensure The Parameter Be Modified Before Downloading!>
============================================================================
Enter your choice(0-5): 0 //选择<0>,返回BootWare主菜单
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System
|<2> Enter Serial SubMenu
|<3> Enter Ethernet SubMenu
|<4> File Control
|<5> Restore to Factory Default Configuration
|<6> Skip Current System Configuration
|<7> BootWare Operation Menu
|<8> Clear Super Password
|<9> Storage Device Operation
|<0> Reboot
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 1 //选择<1>,启动系统即可完成版本升级
-