STM32 TIM PWM高阶操作：刹车及状态约束

news/2024/11/27 23:44:18/

STM32 TIM PWM高阶操作：刹车及状态约束

刹车及状态约束是STM32 TIM PWM控制里面比较复杂的一部分，涉及到PWM波形产生前，中，后的管脚状态输出。

这里先引入两个描述，一个是“半高阻”，意思是STM32管脚输出高阻时，内部的上拉或者下拉设置仍然有效。一个是“全高阻”，意思是STM32管脚输出高阻时，内部上拉或者下拉也被断开，是完全的高阻态输出。

STM32 PWM 刹车特性

所谓刹车（Break, Shut-Down）是指在PWM信号输出过程中，接收到触发信号，停止PWM信号的输出。而PWM信号停止之前之后输出什么状态，则是需要明确设定，避免负载端出现异常。而刹车以及再出发也有相应的控制机制。

刹车实际上有快刹（Break，信号控制停止）和慢刹（Stop, 指令控制停止）两种方式，一般情况下慢刹也够用，所以快刹的详细介绍文章较少。这里会对慢刹和快刹都进行操作介绍。

以STM32F030K6T6芯片及STM32CUBEIDE开发环境为例，首先在TIM1配置一对互补PWM输出通道，设置为40KHz的PWM输出。

配置工作时钟为40MHz：
在这里插入图片描述设置一对PWM互补输出：
在这里插入图片描述
设置为40KHz输出PWM：
在这里插入图片描述
在这里插入图片描述

STM32 PWM 慢刹机制

上述设置保存生成工程初始代码后，就可以在main函数里while循环前启动PWM，对于正通道CH的启动代码为：

HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);

而反通道CHN的启动代码为：

HAL_TIMEx_PWMN_Start(&htim1,TIM_CHANNEL_1);

所以对于互补通道而言，正通道和反通道是各自启动，不是一个启动代码/指令实现正反通道同步启动。另外一方面，虽然正反通道可以不同时启动，但只要都启动了，就会按照配置时的输出电平相位关系输出。也就是说，后启动的通道并不是一定从一个脉冲的前沿电平开始输出，而是与先启动的通道从耦合着的相位电平输出。

慢刹车机制有两种，一种是实时代码停止PWM输出，此后PWM管脚进入半高阻态，如果没有设置内部上拉或下拉，则等同于进入全高阻态。如果设置了内部上拉或下拉，则由上拉电平决定PWM管脚电平。对于正通道CH的停止代码为：

HAL_TIM_PWM_Stop(&htim1,TIM_CHANNEL_1);

对于反通道CHN的停止代码为：

HAL_TIMEx_PWMN_Stop(&htim1,TIM_CHANNEL_1);

在没有内部上拉或下拉，并且外部无连接影响电平时，高阻输出的状态，对于万用表和示波器测的结果是0V状态。如果要重新进入PWM运行状态，只需要重新启动HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);和HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);即可。

另一种慢刹机制是实时代码关闭PWM模式，此后PWM管脚进入全高阻态，内部上拉或下拉无效。如果要重新进入PWM模式，需要重新初始化。
正通道和反通道的PWM模式关闭代码为：

	  HAL_TIM_Base_DeInit(&htim1);

而当需要重新进入PWM模式，则需要初始化:

MX_TIM1_Init();

然后再使用HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);和HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);即可。

由上面介绍可知，再TIM1初始化PWM后，但没有输出PWM信号前，是半高阻态，如果设置了上拉或下拉，就会影响PWM信号输出前的默认电平状态。

STM32 PWM 快刹机制

快刹机制刹车信号的输入有三种： BRK, BRK_ARTH, BRK2, 对于具体的某一个TIM，能用于刹车输入的是上述三种的子集。如：
在这里插入图片描述
在这里插入图片描述
相关的刹车输入信号描述，可以参考官方的文档 Using STM32 device PWM shut-down features 。

这里主要基于BKIN–>BRK来描述PWM的刹车控制的机制和时序。

STM32 PWM BKIN快刹

首先，在PWM配置界面使能刹车输入：
在这里插入图片描述
这是总的刹车输入开关，一旦使能，自动会使能BRK输入:
在这里插入图片描述
实际上，这个时候还可以关闭BRK输入使能，而刹车输入开关不受影响，意味着虽然BRK输入关闭了，但是BRK_ARTH, BRK2刹车输入仍有效（当然也要先做相关输入配置）：
在这里插入图片描述
这里需要采用BRK作为刹车输入，所以将其再使能：
在这里插入图片描述
刹车输入开关（Active-Break-Input）使能后, BKIN管脚就被征用了，不管后面设置是否使能BRK刹车输入。对于STM32F030K6T6, TIM1的BKIN管脚是PA6：
在这里插入图片描述BRK Polarity是选择BRK的刹车有效电平，也就是选择BKIN管脚作为刹车输入的有效电平。BRK Polarity为High时，BKIN管脚收到上升沿电平后会产生PWM信号输出的刹车；BRK Polarity为Low时，BKIN管脚收到下降沿电平后会产生PWM信号输出的刹车；
PA5管脚靠近PA6管脚，将两个管脚短路帽短接，就可以通过PA5输出刹车信号给PA6刹车输入管脚，实现刹车的测试，将PA5管脚配置为输出：
在这里插入图片描述
在配置BRK Polarity为High时，用以下代码可以通过示波器测试刹车的功能：

/* USER CODE BEGIN Header */
/********************************************************************************* @file           : main.c* @brief          : Main program body******************************************************************************* @attention** Copyright (c) 2022 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************Written by Pegasus Yu in 2022*/
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes *//* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD *//* USER CODE END PTD *//* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD *//* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*/
TIM_HandleTypeDef htim1;/* USER CODE BEGIN PV *//* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_TIM1_Init(void);
/* USER CODE BEGIN PFP */
__IO float usDelayBase;
void PY_usDelayTest(void)
{__IO uint32_t firstms, secondms;__IO uint32_t counter = 0;firstms = HAL_GetTick()+1;secondms = firstms+1;while(uwTick!=firstms) ;while(uwTick!=secondms) counter++;usDelayBase = ((float)counter)/1000;
}void PY_Delay_us_t(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t usNum = (uint32_t)(Delay*usDelayBase);delayReg = 0;while(delayReg!=usNum) delayReg++;
}void PY_usDelayOptimize(void)
{__IO uint32_t firstms, secondms;__IO float coe = 1.0;firstms = HAL_GetTick();PY_Delay_us_t(1000000) ;secondms = HAL_GetTick();coe = ((float)1000)/(secondms-firstms);usDelayBase = coe*usDelayBase;
}void PY_Delay_us(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t msNum = Delay/1000;__IO uint32_t usNum = (uint32_t)((Delay%1000)*usDelayBase);if(msNum>0) HAL_Delay(msNum);delayReg = 0;while(delayReg!=usNum) delayReg++;
}/* USER CODE END PFP *//* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 *//* USER CODE END 0 *//*** @brief  The application entry point.* @retval int*/
int main(void)
{/* USER CODE BEGIN 1 *//* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_TIM1_Init();/* USER CODE BEGIN 2 */PY_usDelayTest();PY_usDelayOptimize();HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET); //no brakeHAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);HAL_TIMEx_PWMN_Start(&htim1,TIM_CHANNEL_1);PY_Delay_us(5000000);HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_SET); //brake/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** @brief System Clock Configuration* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;RCC_OscInitStruct.HSIState = RCC_HSI_ON;RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL10;RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK){Error_Handler();}
}/*** @brief TIM1 Initialization Function* @param None* @retval None*/
static void MX_TIM1_Init(void)
{/* USER CODE BEGIN TIM1_Init 0 *//* USER CODE END TIM1_Init 0 */TIM_MasterConfigTypeDef sMasterConfig = {0};TIM_OC_InitTypeDef sConfigOC = {0};TIM_BreakDeadTimeConfigTypeDef sBreakDeadTimeConfig = {0};/* USER CODE BEGIN TIM1_Init 1 *//* USER CODE END TIM1_Init 1 */htim1.Instance = TIM1;htim1.Init.Prescaler = 3;htim1.Init.CounterMode = TIM_COUNTERMODE_UP;htim1.Init.Period = 249;htim1.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;htim1.Init.RepetitionCounter = 0;htim1.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;if (HAL_TIM_PWM_Init(&htim1) != HAL_OK){Error_Handler();}sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;if (HAL_TIMEx_MasterConfigSynchronization(&htim1, &sMasterConfig) != HAL_OK){Error_Handler();}sConfigOC.OCMode = TIM_OCMODE_PWM1;sConfigOC.Pulse = 0;sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;sConfigOC.OCNPolarity = TIM_OCNPOLARITY_HIGH;sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;sConfigOC.OCIdleState = TIM_OCIDLESTATE_RESET;sConfigOC.OCNIdleState = TIM_OCNIDLESTATE_RESET;if (HAL_TIM_PWM_ConfigChannel(&htim1, &sConfigOC, TIM_CHANNEL_1) != HAL_OK){Error_Handler();}sBreakDeadTimeConfig.OffStateRunMode = TIM_OSSR_DISABLE;sBreakDeadTimeConfig.OffStateIDLEMode = TIM_OSSI_DISABLE;sBreakDeadTimeConfig.LockLevel = TIM_LOCKLEVEL_OFF;sBreakDeadTimeConfig.DeadTime = 0;sBreakDeadTimeConfig.BreakState = TIM_BREAK_ENABLE;sBreakDeadTimeConfig.BreakPolarity = TIM_BREAKPOLARITY_HIGH;sBreakDeadTimeConfig.AutomaticOutput = TIM_AUTOMATICOUTPUT_DISABLE;if (HAL_TIMEx_ConfigBreakDeadTime(&htim1, &sBreakDeadTimeConfig) != HAL_OK){Error_Handler();}/* USER CODE BEGIN TIM1_Init 2 *//* USER CODE END TIM1_Init 2 */HAL_TIM_MspPostInit(&htim1);}/*** @brief GPIO Initialization Function* @param None* @retval None*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};/* GPIO Ports Clock Enable */__HAL_RCC_GPIOA_CLK_ENABLE();/*Configure GPIO pin Output Level */HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);/*Configure GPIO pin : PA5 */GPIO_InitStruct.Pin = GPIO_PIN_5;GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;GPIO_InitStruct.Pull = GPIO_NOPULL;GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//*** @brief  This function is executed in case of error occurrence.* @retval None*/
void Error_Handler(void)
{/* USER CODE BEGIN Error_Handler_Debug *//* User can add his own implementation to report the HAL error return state */__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef  USE_FULL_ASSERT
/*** @brief  Reports the name of the source file and the source line number*         where the assert_param error has occurred.* @param  file: pointer to the source file name* @param  line: assert_param error line source number* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

上述代码实现了驱动一组互补PWM输出5秒后，PA5输出刹车信号，PA6接收到刹车信号后，将PWM的输出刹车关闭。其中，延时函数PY_Delay_us()的原理参考 STM32 HAL us delay（微秒延时）的指令延时实现方式及优化 。

STM32 PWM BKIN快刹后恢复PWM输出

STM32 PWM BKIN快刹后恢复PWM输出有两种方式，和Automatic Output Status参数有关：
在这里插入图片描述
Automatic Output Status为Disable时，不能通过BRK刹车输入信号的电平反向恢复PWM输出,而需要重新初始化TIM和使能PWM输出。如下的代码对应刹车5秒后重新恢复TIM PWM输出，注意这里刹车后只使能PWM输出没有重新初始化TIM是无效的：

/* USER CODE BEGIN Header */
/********************************************************************************* @file           : main.c* @brief          : Main program body******************************************************************************* @attention** Copyright (c) 2022 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************Written by Pegasus Yu in 2022*/
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes *//* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD *//* USER CODE END PTD *//* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD *//* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*/
TIM_HandleTypeDef htim1;/* USER CODE BEGIN PV *//* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_TIM1_Init(void);
/* USER CODE BEGIN PFP */
float usDelayBase;
void PY_usDelayTest(void)
{uint32_t firstms, secondms;uint32_t counter = 0;firstms = HAL_GetTick()+1;secondms = firstms+1;while(uwTick!=firstms) ;while(uwTick!=secondms) counter++;usDelayBase = ((float)counter)/1000;
}void PY_Delay_us_t(uint32_t Delay)
{uint32_t delayReg;uint32_t usNum = (uint32_t)(Delay*usDelayBase);delayReg = 0;while(delayReg!=usNum) delayReg++;
}void PY_usDelayOptimize(void)
{uint32_t firstms, secondms;float coe = 1.0;firstms = HAL_GetTick();PY_Delay_us_t(1000000) ;secondms = HAL_GetTick();coe = ((float)1000)/(secondms-firstms);usDelayBase = coe*usDelayBase;
}void PY_Delay_us(uint32_t Delay)
{uint32_t delayReg;uint32_t msNum = Delay/1000;uint32_t usNum = (uint32_t)((Delay%1000)*usDelayBase);if(msNum>0) HAL_Delay(msNum);delayReg = 0;while(delayReg!=usNum) delayReg++;
}/* USER CODE END PFP *//* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 *//* USER CODE END 0 *//*** @brief  The application entry point.* @retval int*/
int main(void)
{/* USER CODE BEGIN 1 *//* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_TIM1_Init();/* USER CODE BEGIN 2 */PY_usDelayTest();PY_usDelayOptimize();HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);//no brakeHAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);HAL_TIMEx_PWMN_Start(&htim1,TIM_CHANNEL_1);PY_Delay_us(5000000);HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_SET);//brakePY_Delay_us(5000000);HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);//no brakeMX_TIM1_Init();HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);HAL_TIMEx_PWMN_Start(&htim1,TIM_CHANNEL_1); //pwm output/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** @brief System Clock Configuration* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;RCC_OscInitStruct.HSIState = RCC_HSI_ON;RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL10;RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK){Error_Handler();}
}/*** @brief TIM1 Initialization Function* @param None* @retval None*/
static void MX_TIM1_Init(void)
{/* USER CODE BEGIN TIM1_Init 0 *//* USER CODE END TIM1_Init 0 */TIM_MasterConfigTypeDef sMasterConfig = {0};TIM_OC_InitTypeDef sConfigOC = {0};TIM_BreakDeadTimeConfigTypeDef sBreakDeadTimeConfig = {0};/* USER CODE BEGIN TIM1_Init 1 *//* USER CODE END TIM1_Init 1 */htim1.Instance = TIM1;htim1.Init.Prescaler = 3;htim1.Init.CounterMode = TIM_COUNTERMODE_UP;htim1.Init.Period = 249;htim1.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;htim1.Init.RepetitionCounter = 0;htim1.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;if (HAL_TIM_PWM_Init(&htim1) != HAL_OK){Error_Handler();}sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;if (HAL_TIMEx_MasterConfigSynchronization(&htim1, &sMasterConfig) != HAL_OK){Error_Handler();}sConfigOC.OCMode = TIM_OCMODE_PWM1;sConfigOC.Pulse = 0;sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;sConfigOC.OCNPolarity = TIM_OCNPOLARITY_HIGH;sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;sConfigOC.OCIdleState = TIM_OCIDLESTATE_RESET;sConfigOC.OCNIdleState = TIM_OCNIDLESTATE_RESET;if (HAL_TIM_PWM_ConfigChannel(&htim1, &sConfigOC, TIM_CHANNEL_1) != HAL_OK){Error_Handler();}sBreakDeadTimeConfig.OffStateRunMode = TIM_OSSR_DISABLE;sBreakDeadTimeConfig.OffStateIDLEMode = TIM_OSSI_DISABLE;sBreakDeadTimeConfig.LockLevel = TIM_LOCKLEVEL_OFF;sBreakDeadTimeConfig.DeadTime = 0;sBreakDeadTimeConfig.BreakState = TIM_BREAK_ENABLE;sBreakDeadTimeConfig.BreakPolarity = TIM_BREAKPOLARITY_HIGH;sBreakDeadTimeConfig.AutomaticOutput = TIM_AUTOMATICOUTPUT_DISABLE;if (HAL_TIMEx_ConfigBreakDeadTime(&htim1, &sBreakDeadTimeConfig) != HAL_OK){Error_Handler();}/* USER CODE BEGIN TIM1_Init 2 *//* USER CODE END TIM1_Init 2 */HAL_TIM_MspPostInit(&htim1);}/*** @brief GPIO Initialization Function* @param None* @retval None*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};/* GPIO Ports Clock Enable */__HAL_RCC_GPIOA_CLK_ENABLE();/*Configure GPIO pin Output Level */HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);/*Configure GPIO pin : PA5 */GPIO_InitStruct.Pin = GPIO_PIN_5;GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;GPIO_InitStruct.Pull = GPIO_NOPULL;GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//*** @brief  This function is executed in case of error occurrence.* @retval None*/
void Error_Handler(void)
{/* USER CODE BEGIN Error_Handler_Debug *//* User can add his own implementation to report the HAL error return state */__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef  USE_FULL_ASSERT
/*** @brief  Reports the name of the source file and the source line number*         where the assert_param error has occurred.* @param  file: pointer to the source file name* @param  line: assert_param error line source number* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

而当Automatic Output Status设置为Enable时，则BRK信号从刹车电平反向后，会自动恢复PWM信号的输出，与上面的方式效果一样，而减少了代码调用逻辑：

在这里插入图片描述

/* USER CODE BEGIN Header */
/********************************************************************************* @file           : main.c* @brief          : Main program body******************************************************************************* @attention** Copyright (c) 2022 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************Written by Pegasus Yu in 2022*/
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes *//* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD *//* USER CODE END PTD *//* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD *//* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*/
TIM_HandleTypeDef htim1;/* USER CODE BEGIN PV *//* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_TIM1_Init(void);
/* USER CODE BEGIN PFP */
float usDelayBase;
void PY_usDelayTest(void)
{uint32_t firstms, secondms;uint32_t counter = 0;firstms = HAL_GetTick()+1;secondms = firstms+1;while(uwTick!=firstms) ;while(uwTick!=secondms) counter++;usDelayBase = ((float)counter)/1000;
}void PY_Delay_us_t(uint32_t Delay)
{uint32_t delayReg;uint32_t usNum = (uint32_t)(Delay*usDelayBase);delayReg = 0;while(delayReg!=usNum) delayReg++;
}void PY_usDelayOptimize(void)
{uint32_t firstms, secondms;float coe = 1.0;firstms = HAL_GetTick();PY_Delay_us_t(1000000) ;secondms = HAL_GetTick();coe = ((float)1000)/(secondms-firstms);usDelayBase = coe*usDelayBase;
}void PY_Delay_us(uint32_t Delay)
{uint32_t delayReg;uint32_t msNum = Delay/1000;uint32_t usNum = (uint32_t)((Delay%1000)*usDelayBase);if(msNum>0) HAL_Delay(msNum);delayReg = 0;while(delayReg!=usNum) delayReg++;
}/* USER CODE END PFP *//* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 *//* USER CODE END 0 *//*** @brief  The application entry point.* @retval int*/
int main(void)
{/* USER CODE BEGIN 1 *//* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_TIM1_Init();/* USER CODE BEGIN 2 */PY_usDelayTest();PY_usDelayOptimize();HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);//no brakeHAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1);HAL_TIMEx_PWMN_Start(&htim1,TIM_CHANNEL_1);PY_Delay_us(5000000);HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_SET);//brakePY_Delay_us(5000000);HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);//no brake & PWM outut/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** @brief System Clock Configuration* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;RCC_OscInitStruct.HSIState = RCC_HSI_ON;RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL10;RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK){Error_Handler();}
}/*** @brief TIM1 Initialization Function* @param None* @retval None*/
static void MX_TIM1_Init(void)
{/* USER CODE BEGIN TIM1_Init 0 *//* USER CODE END TIM1_Init 0 */TIM_MasterConfigTypeDef sMasterConfig = {0};TIM_OC_InitTypeDef sConfigOC = {0};TIM_BreakDeadTimeConfigTypeDef sBreakDeadTimeConfig = {0};/* USER CODE BEGIN TIM1_Init 1 *//* USER CODE END TIM1_Init 1 */htim1.Instance = TIM1;htim1.Init.Prescaler = 3;htim1.Init.CounterMode = TIM_COUNTERMODE_UP;htim1.Init.Period = 249;htim1.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;htim1.Init.RepetitionCounter = 0;htim1.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;if (HAL_TIM_PWM_Init(&htim1) != HAL_OK){Error_Handler();}sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;if (HAL_TIMEx_MasterConfigSynchronization(&htim1, &sMasterConfig) != HAL_OK){Error_Handler();}sConfigOC.OCMode = TIM_OCMODE_PWM1;sConfigOC.Pulse = 0;sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;sConfigOC.OCNPolarity = TIM_OCNPOLARITY_HIGH;sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;sConfigOC.OCIdleState = TIM_OCIDLESTATE_RESET;sConfigOC.OCNIdleState = TIM_OCNIDLESTATE_RESET;if (HAL_TIM_PWM_ConfigChannel(&htim1, &sConfigOC, TIM_CHANNEL_1) != HAL_OK){Error_Handler();}sBreakDeadTimeConfig.OffStateRunMode = TIM_OSSR_DISABLE;sBreakDeadTimeConfig.OffStateIDLEMode = TIM_OSSI_DISABLE;sBreakDeadTimeConfig.LockLevel = TIM_LOCKLEVEL_OFF;sBreakDeadTimeConfig.DeadTime = 0;sBreakDeadTimeConfig.BreakState = TIM_BREAK_ENABLE;sBreakDeadTimeConfig.BreakPolarity = TIM_BREAKPOLARITY_HIGH;sBreakDeadTimeConfig.AutomaticOutput = TIM_AUTOMATICOUTPUT_ENABLE;if (HAL_TIMEx_ConfigBreakDeadTime(&htim1, &sBreakDeadTimeConfig) != HAL_OK){Error_Handler();}/* USER CODE BEGIN TIM1_Init 2 *//* USER CODE END TIM1_Init 2 */HAL_TIM_MspPostInit(&htim1);}/*** @brief GPIO Initialization Function* @param None* @retval None*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};/* GPIO Ports Clock Enable */__HAL_RCC_GPIOA_CLK_ENABLE();/*Configure GPIO pin Output Level */HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);/*Configure GPIO pin : PA5 */GPIO_InitStruct.Pin = GPIO_PIN_5;GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;GPIO_InitStruct.Pull = GPIO_NOPULL;GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//*** @brief  This function is executed in case of error occurrence.* @retval None*/
void Error_Handler(void)
{/* USER CODE BEGIN Error_Handler_Debug *//* User can add his own implementation to report the HAL error return state */__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef  USE_FULL_ASSERT
/*** @brief  Reports the name of the source file and the source line number*         where the assert_param error has occurred.* @param  file: pointer to the source file name* @param  line: assert_param error line source number* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

STM32 PWM BKIN快刹后PWM管脚输出状态

刹车后的默认管脚状态也是必要的设计要点。涉及到OSSI选项的控制。
在这里插入图片描述

注意Break And Dead Time Management里面的几项是独立的关系，譬如Automatic Output State设置成Enable或Disable不影响其余几项的实施。

OSSI使能后，CH IDLE STATE和CHN IDLE STATE才有效，用于设定刹车后的管脚状态输出。OSSI不使能，刹车后的管脚输出半高阻态，这时候CH IDLE STATE和CHN IDLE STATE的设置无任何效果。
在这里插入图片描述

STM32 PWM 互补输出的不补输出转态

STM32 PWM互补输出的不补输出转态和OSSR参数相关：
在这里插入图片描述
OSSR不使能，当互补输出正反两路的一路使能输出而另一路没有使能输出，没有使能输出的一路则输出半关闭高阻态，可以使用内部上下拉控制管脚状态。OSSR使能，当互补输出正反两路的一路使能输出而另一路没有使能输出，没有输出的一路则输出全关闭高阻态，内部上下拉无效。

STM32 PWM LOCK CONFIGURATION

因为PWM常用于控制功率输出负载，如果出现异常STM32程序跑飞，导致配置的寄存器混乱，进一步导致PWM输出异常，则会造成风险。Lock Configuration使能后，会形成保护机制，简而言之就是MCU启动后，代码配置Lock保护级别后，在下次重启前相关输出配置不能被修改。
在这里插入图片描述
有三个保护级别，Lock Level 3的保护级别最高。一般采用Lock Level 1即可，会在下次复位前冻结TIMx_BDTR 寄存器中的
DTG/BKE/BKP/AOE/BKF/BK2F/BK2E/BK2P 位，以及TIMx_CR2 寄存器中的OISx/OISxN位。

–End–


http://www.ppmy.cn/news/10911.html

相关文章

vue+xlsx实现表格的导入导出:

vue+xlsx实现表格的导入导出:

文章目录一、vue前端使用xlsx和 xlsx-style 导出excel，并修改样式:1、改造后效果：2、实现：3、引入库xlsx-style4、excelUtil.js文件二、前端xlsx插件怎么设置导出的excel列宽自适应？2-1、效果2-2、效果三、xlsx插件，导…
阅读更多...
元年科技2022回顾：奋楫扬帆数字化，转型升级立潮头

元年科技2022回顾：奋楫扬帆数字化，转型升级立潮头

当下数字经济无疑以最具创新、辐射力最广泛的经济形态迸发着无限活力，这也意味着数字化转型的浪潮风起云涌。作为数字化转型的主力军，元年科技肩负重任奋楫扬帆，在沧海中勇往直前。 回顾2022年，元年科技在不断走向深入的数字化转…
阅读更多...
Vue3——第四章（响应式基础：reactive、ref）

Vue3——第四章（响应式基础：reactive、ref）

一、用reactive()声明响应式状态 我们可以使用 reactive() 函数创建一个响应式对象或数组： 响应式对象其实是 JavaScript Proxy，其行为表现与一般对象相似。不同之处在于 Vue 能够跟踪对响应式对象属性的访问与更改操作。 要在组件模板中使用响应式状…
阅读更多...
【Linux】Linux 项目自动化构建工具 -- make/makefile

【Linux】Linux 项目自动化构建工具 -- make/makefile

👑作者主页：进击的安度因 🏠学习社区：进击的安度因（个人社区） 📖专栏链接：Linux 文章目录一、前言二、概念三、demo 实现四、原理与规则1、依赖关系和依赖方法① 感性理解② 深层理解…
阅读更多...
计算机网络培训总结

计算机网络培训总结

在11月份我参加了这次计算机网络培训，虽然这次计算机网络培训的时间很短，但对我来说受益匪浅,充分认识到了自己在计算机应用与网络方面存在很多不足。培训使我的眼界开阔了、思考问题的角度改变了， 许多疑问得到了解决或者启发。 作为一名信息…
阅读更多...
STL空间配置器框架分析

STL空间配置器框架分析

目录 一、空间配置器概念 二、空间配置器的作用 三、内存池技术 四、空间配置器的实现原理 3.1 流程概述 3.2 一级空间配置器 3.3 二级空间配置器 3.3.1 二级空间配置器设计 3.3.2 内存碎片问题 一、空间配置器概念 即为各个容器高效的管理空间(空间的申请与回收)的。…
阅读更多...
分享48个Go源码，总有一款适合您

分享48个Go源码，总有一款适合您

Go源码 分享48个Go源码，总有一款适合您 Go源码下载链接：https://pan.baidu.com/s/1FhQ6NzB3TWsv9res1OsJaA?pwdr2d3 提取码：r2d3 下面是文件的名字，我放了一些图片，文章里不是所有的图主要是放不下...，…
阅读更多...
Linux 环境使用定时任务执行shell脚本

Linux 环境使用定时任务执行shell脚本

前言：Linux添加定时任务需要依赖crond服务，如果没有该服务，需要先安装：yum -y install crontabs 1、crond服务相关命令介绍 启动crond服务：service crond start 停止crond服务：service crond stop 重启cro…
阅读更多...
最新文章

Copyright @ 2022~2023